Re-purpose old window frames into photo fames {Part 2}

Remember this post?
I did it 5 months ago! 5 months? Where on earth does the time go? I had every intention of doing part 2 sooner than this...but nonetheless, here is part 2.
I hope this answers any questions I got in part 1.

I left off with the wood work of the frame completely finished.
Now let's carry on from there...

1. Putting The glass back in.

So I didn't get any photos of this part,(sorry) but it is really quite straight forward.
Before I begin, a few notes:
If you are going to use the original glass, you just need to fit each panel back into the right place. Sometimes
the sizes are slightly out by a few mm, so you might need to check each piece of glass until you have the right one for each place.
Or, you can do what I did. I like the "old" looking frame work, but wanted clean,new glass as I was putting photos into the frame. So I carefully measured each individual little frame within the frame and made a note of each measurement. Be sure to measure to within the last 2-3mm all around. This Leaves a very small gap to get the glass in. (I measured from side to side all around and then subtracted 2mm all the way around )
Take your measurements to your local glass cutter and they will cut each piece for you. This is very cheap to have done, for the new glass and labor.

So getting back to putting the glass in...
-make sure your framework is clean and completely free of any residue or dust. A good vacuum or sweep will do the trick!
-Double check the back of the frame where you took the grout out,that it is completely free of lumps and bumps and if need be, sand down any forgotten or missed areas.
-I used no more nails. Simply squeeze a line around the border of the panel (working one panel at a time)
Then insert your glass and press down gently but firmly (only on the sides , don't press the glass in the middle-you could break it). Press it down enough so that the excess solvent squeezes out.
You should wipe this off with kitchen paper and have a damp cloth nearby to clean the glass  as the stuff is a pain to get off once it dries.
Carry on with the rest of the panels in this fashion.
WARNING: wear old clothes and rubber gloves when you are doing this and make sure your surface is covered in newspaper, this stuff is MESSY!

After each panel of glass is in, clean and neat, leave it as is to dry overnight.

{note: For photos you can use a 3mm glass. the thicker you go, the heavier your frame will be and the more expensive your glass will be. 3mm is quite adequate if you are using it as a photo frame. }

2. Backing Board

Again, I measured each frame and then subtracted about 2mm all the way around. I got the wood cut (just used ordinary chipboard)

We drilled a small hole into each adjacent corner of each panel (so 8 holes for each panel in the inside of the frame work -at the back). He made these little metal hooks for me and inserted one into each place. They act as a kind of spring, holding the board down. But you could use normal black blips you find on the back of any photo frame that are inserted into the woodwork of the frame. We just couldn't find them anywhere and so had to make our own plan.
Ask your local framer or hardware store.

And that is it! Here is my frame finished and hanging in my dining room!

Re-purose old Windows into Photo Frames {Part 1}

If you are a regular to my blog, you will know that I love to create.

I also love a good project, especially when it involves something for my home. Be it creating new cushion covers, crocheting a blanket, making curtains or blinds, painting a new color on the walls or simply re-arranging the furniture!

Last year for our anniversary, my hubby bought me a gorgeous photo frame. This is no ordinary photo frame. It is an old window (with 6 panes) that had been converted. And made to look pretty shabby-chic. The more "old" something looks, the more I love it! I was so happy as I had been wanting one for ages. I finally had a place to put all the kids pre-school professional photo's into.

However, since then I wanted more of these frames. They are just fabulous if you have a "collection" of photos you want to display.

Then recently I got a call from my mom in law to tell me she saw some old window frames on the sidewalk of a second hand business, going for really cheap. So I zapped down and sure enough, they were going for only R55! {$6.60 or £4.22} each. So I bought two.
Buying one from a gift/decor shop you could easily pay between R800-R1000 {$96-$121 or 61 -£76}.
Um...hello? R800 or R55? {$96 or $6.60?? £61 or £4.22??}

I was sooooo excited! It has taken about two weeks but I have finished all the hard work.

1. Taking Out the old grout.
Firstly, before doing anything, you need to remove the old grout. All you need is a pair of gloves, a wood chisel and a hammer. The smaller window took me a few hours over two days to do as the grout was very hard-the window seemed quite new still.
Tapping the wood chisel gently with the hammer along the edge where the grout meets the wood frame will help to loosen it and then you can work the chisel into it and begin to pry it off.

Before

After

The second window was much easier and took me just over an hour to do the whole 10-paned frame! The grout was really soft.

Here is when you also fix any lifting wood or large cracks in the frame before proceeding. My hubby kindly glued for me and clamped it down for a few hours and was as good as new!

2. Taking The Glass out
This can be quite easy or tricky depending on how you handle the wood chisel and hammer. If you are too rough and tap the chisel too roughly or in the wrong spot, you could crack the glass.
For me, even though I had planned to get new glass (old glass was full of old paint, grout and scratches) I still wanted to be careful because let's face it, working with cut glass is dangerous and no fun! I think I only cracked 3 panes! One piece was already shattered when I bought it.
If the glass is still in good condition you could clean it up and re-use it. Sometimes all it takes is a bit of a scrape and some elbow-grease. But as in my case, the glass was scratched. I like "old" and shabby chic, but there is a limit!

3.Sanding the Frame down
The next step, once all the grout and glass is removed, is to give your frame a light sand. I used a power sander for this (my first time!!) and it was really easy once I got into the groove of handling the tool. Make sure you use a fine sandpaper, too rough and you will strip all the old paint off. In my case, going for the shabby-chic look I didn't have to do that.

The smaller window was already painted with a nice coat of white paint but the second window was dark and covered with a thick varnish which I didn't like at all, so I sanded it down as much as I could.

Just a note: I didn't bother about sanding the varnish off the back of the larger window as it won't be seen!

I also used the sander to smooth the edges, especially where I had taken off the hinges and taken out old nails. You don't want wood splinters! Also important is to try get into the crevices at the back, cos that is where your new glass and backing boards are going to go, so you really want to get rid of any old grout.

4. Painting.
So after you have sanded, give the window a brush down just to get rid of any wood residue left from sanding. You can now paint your first coat. I used a white enamel acrylic paint. I didn't bother with a wood primer as these windows are purely for inside decoration!

After the paint dried, I gave it another light sand and then applied a second coat onto both windows and left to dry.

5. Getting that "old" look
The fun part is the final part! If your windows were second hand, no doubt they already has some dents, tears, scratches, holes etc. This all adds to the character if you want a shabby-chic look. So you actually want to accentuate these flaws. These are the parts you want to sand down to reveal the wood underneath. I used a medium sand paper and did these by hand.
You also want to concentrate on sanding the corners, edges and joins.
You don't want to overdo it, just hear and there.

I know some people like to paint a dark color first and then a white and then sand through the white to see the dark color, but I like the wood look, it looks more natural.
I then used a dark ink chalk stamp pad(like the one you use for scrap booking!)
I used a "Pretty color #37) to accentuate the rough spots and edges.

So far all it has cost me is exactly what I paid, as I already had sandpaper, the tools and paint at home!

I worked out that with the new glass and photo enlargements it will still cost me a fraction of what I would pay new in a shop (without the photos!). In the photo below you can see the after result and a peek of the frame that was shop-bought!

All mine need now is new glass and photos!

I got sandpaper/paint happy and went searching for other things to redo! Old mirror frames!
Aha!

Look out for part 2.
{when I finish them with the glass, baking board, and photos} coming soon....